Categories
Site news
-
05/22/2013
صورة من داخل اسوار المصنع Read The Full Story
-
04/28/2013
مشاركة في معرض بروجكت قطر Read The Full Story
-
04/01/2013
توقيع عقد وكالة Read The Full Story
-
03/31/2013
مشاركة في معرض عمان لمواد البناء Read The Full Story
-
06/07/2012
مرحبا بكم في شركة مصنع الاتحاد Read The Full Story
ULM 1000ELASTOMERIC LIQUID APPLIED MEMBRANE |
DESCRIPTION
ULM 1000 (Uni Liquid Membrane 1000) is a superior quality, elastomeric, liquid applied bitumen membrane blended with special ingredients. It is solvent based with special SBS rubber for high quality performance and durability. The elastomeric liquid applied membrane forms upon drying a tough elastic, flexible coating capable to withstand structural movements and moisture penetration.
FEATURES AND BENEFITS
- Forms a tough and elastic waterproof film upon drying
- High elasticity (Exceeds 1000% elongation)
- Excellent elastomeric protective coating
- Highly flexible
- Anti-corrosion properties
- Bridges minor cracks
- Seamless and adaptable to irregular surface
- Compatible with other bituminous products
- Excellent bonding and adhesion properties
- Cold applied; easy application
MAIN USES
ULM 1000 is used in
- Wet areas - Kitchens, bathrooms, balconies and shower rooms.
- Elastomeric liquid applied membrane for foundation, cellar walls.
- Non-potable water tanks, sewage tanks and tunnels.
- Liquid applied coating on vertical surfaces.
- Parking decks, planters, and damp floors.
METHOD OF APPLICATION
Substrate Preparation
- All substrate must be clean, free from dirt, dust, soil, grease, oil and other loose particles. Substrates that are very dry should be applied with a penetrative coating of UNIPRIME.
- Stir the solution thoroughly if stored for a long time.
Application on Porous substrates (e.g. Concrete Structure)
- Prime the surface with solvent based primer UNIPRIME and allow the primer to dry completely (6-8 hours).
- Apply a minimum of 2 coats by brush or spray equipment.
- The second coat is applied when the first coat has completely dried.
- Apply each coat at a right angle to the previous one to achieve good coverage and uniformity.
- A third coat is required for very porous substrates.
- Drying time is 1-4 hours under normal conditions. Under damp and cold conditions it is recommended to allow 6 hours between successive coats.
PACKING AND STORAGE
ULM 1000 is available in 20-liter pails and 200-liter drums, palletized and strapped. Shelf life is minimum of 6-months in a tightly closed container. Avoid direct exposure to heat and sunlight. The product has to be thoroughly mixed.
HEALTH AND SAFETY
ULM 1000 is solvent base that gives out inflammable vapor. Proper care must be taken when applying the coating. Wear proper or necessary Personal Protective Equipment, ensure proper ventilation if used in enclosed area, keep away from sources of ignition, and avoid contact with skin, eyes or inhalation. Make sure that the container is closed after each application. Refer to our MSDS sheets for advice.
TECHNICAL DATA
PROPERTY |
UNIT |
VALUE |
TEST METHOD |
Total Solids |
% |
65 ± 5 |
ASTM D 2369 |
Elongation |
% |
>1000 |
ASTM D 638-95 |
Recovery |
% |
>96 |
ASTM D638-95 |
Density |
Kg/L |
0.90 to 0.95 |
ASTM D 70 |
Firm Set |
hrs |
24 |
In house |
Coverage |
Kg/m2 |
0.5 – 1.1 |
- |
CLEANING OF TOOLS
The brush and spray equipment should be cleaned immediately after use by means of a suitable solvent like white spirit, Petrol or Diesel oil.